Separation and fractionation of glutamic acid and histidine via origami isoelectric focusing.

We demonstrated the fractionation of two amino acids, glutamic acid and histidine, separated via isoelectric focusing (IEF) on filter paper folded and stacked in an origami fashion. Channels for electrophoresis were fabricated as circular zones acquired via wax printing onto the filter paper. An ampholyte solution with amphiphilic samples was deposited on all the circle zones, which was followed by folding to form the electrophoresis channels. IEF was achieved by applying an electrical potential between the anodic and cathodic chambers filled with phosphoric acid and sodium hydroxide solutions, respectively. A pH gradient was formed using either a wide-range ampholyte with a pH of 3 to 10 or a narrow-range version with a pH of 5 to 8, which was confirmed by adding pH indicators to each layer. The origami IEF was used to separate the amino acids, glutamic acid and histidine, by mixing with the ampholytes, which were deposited on the layers. The components in each layer were extracted with water and measured by high-performance liquid chromatography using pre-column derivatization with dansyl chloride. The results indicated that the focus for glutamic acid and that for histidine were at different layers, according to their isoelectric points. The origami isoelectric focusing achieved the fractionation of amino acids in less than 3 min using voltage as low as 30 V.

Development of Pipetteless Paper-Based Analytical Devices with a Volume Gauge.

In this work, we propose a new design for paper-based analytical devices (PADs) that eliminate the need to use a micropipette for sample introduction. With this design, a PAD is equipped with a distance-based detection channel that is connected to a storage channel that indicates the volume of a sample introduced into the PAD. The analyte in the sample solution reacts with a colorimetric reagent deposited into the distance-based detection channel as the sample solution flows into the storage channel where the volume is measured. The ratio of the lengths of the detection channel and that of the storage channel (D/S ratio) are constant for a sample containing a certain concentration, which is independent of the introduced volume. Therefore, the PADs permit volume-independent quantification using a dropper instead of a micropipette because the length of the storage channel plays the role of a volume gauge to estimate the introduced sample volume. In this study, the D/S ratios obtained with a dropper were comparable to those obtained with a micropipette, which confirmed that precise volume control is unnecessary for this PAD system. The proposed PADs were applied to the determinations of iron and bovine serum albumin using bathophenanthroline and tetrabromophenol blue as colorimetric reagents, respectively. The calibration curves showed good linear relationships with coefficients of 0.989 for iron and 0.994 for bovine serum albumin, respectively.

WinMLR program for the determination of sorbic and benzoic acids in food samples.

The program WinMLR has been developed to quantify sorbic and benzoic acids in soft drinks, fruit juices, and soy sauce by making a multilinear regression treatment of experimental data to a linear combination of standard signals. The spectra of sorbic and benzoic acid and samples were obtained from a conventional spectrophotometer, which has been saved in an ASCII file to be applied with the WinMLR program. Before to determine sorbic and benzoic acids in samples, the wavelength validation and calibration parameters were studied. Standard solutions of sorbic and benzoic acids were used for the calibration parameters to measure the individual analyte. If the sample has simultaneously both compounds, it is better to choose the synthetic mixture for the calibration parameters. This technique provides a good recovery in the range of 80.4-104.8% without a complicated and expensive instrument.

Design of an automatic spectrophotometric system.

A Multi-Syringe Flow Injection Analysis (MSFIA) fluorometric system based on a 3D printing device hosting a CCD detector has been designed for the determination of quinine in soft drinks. A LED controlled by an electronic circuit was used as a radiation source. The entire system is connected to two USB outputs of a computer. The AutoAnalysis program has been used for data acquisition and treatment. The results are more accurate and precise than those obtained with a manual method using a conventional spectrofluorometer. This developed system is a viable alternative to reduce the consumption of reagents, the impact on the environment and reduce measurement costs.

Design of a portable spectrophotometric system part II: Using a digital microscope as detector.

A simple, cheap and portable spectrophotometric system is described. It is based on the use of a cheap digital microscope housed from a 3D printed device which simultaneously supports a LED as a light source and a flow cell. A simple electronic device to power the LED is also described using electronic smd components. Both the digital microscope and the power source required to light the LED are connected to the USB ports of a notebook in order to avoid the need of any power source to complete the portable system. This method was applied to make the determination of Fe2+ with o-phenanthroline as chromogenic reagent. The reaction provided the red complex which is used to monitor the analytical response with the digital microscope.

WinMLR, a software program for the simultaneous determination of several components in mixtures using multilinear regression analysis.

The program WinMLR has been developed for the quantification of mixtures of several components by making a multilinear regression treatment of experimental data to a linear combination of standard signals. Data may be obtained with any multichannel detector having more measuring channels than components to be resolved. For a correct resolution, a linear relationship between the signal of every channel and the component concentration is required. The data must be located into ASCII files, one file for each standard or sample measurement, which contain the X and Y values in separated columns. The program allows three types of calibration methods: single standard, multiple standards and multiple standards addition. In the first case, the program requires to measure one standard per component. In the second case, the user can employ standards of both pure compounds and known mixtures under the sole constraint that the set of standards must include all components in different proportions. Similarly, the multiple standard addition method (more known as general standard addition method) requires the data obtained by adding known amounts of one or several mixture components to the sample so that all of them are included in the assays. In the multiple standards and multiple standards addition procedures, once the calibration has been done, the program allows the mixture to be resolved by weighted or unweighted regression.

Spectrophotometric system based on a device created by 3D printing for the accommodation of a webcam chamber as a detection system.

The development of a simple and economical spectrophotometric system based on the use of a device created by 3D printing and the electronics necessary to control the intensity of the radiation source was described. The measurements are made with a low-cost digital webcam. The entire system is only powered through the USB outputs of a computer, which makes the portable and really practical system for the measurements in the field. This method was applied to determine iron (II) in waters using o-phenanthroline as chromogenic reagent giving a red complex, and also to hypochlorite determination using tetramethylbenzidine as the reagent providing a yellow color. The calibration curves were built using a mathematical algorithm making a RGB deconvolution. The intense of colors obtained from a webcam in each concentration of analyte had a relationship with the absorbance values. In order to confirm the accuracy and precision of this method, a traditional spectrophotometer was used for validation.

Multisyringe flow injection analysis (MSFIA) for the automatic determination of total iron in wines.

This work presents a multisyringe flow injection analysis (MSFIA) system for the automatic spectrophotometric determination of total iron in wine. The reaction is based on the complexation of Fe(II) with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (Br-PADAP). Ascorbic acid was used as reducing reagent for Fe(III) to Fe(II) and, in this way, to determine the total iron content in wine. The absorbance of the Fe(II)-(Br-PADAP)2 complex was measured at 748 nm. The proposed method provided a working rage from 0.36 to 5 mg L-1 of Fe(II), with a detection limit of 0.11 mg L-1 of Fe(II), a relative standard deviation of 0.42% (3 mg L-1 of Fe(II), n = 10), and a 46 h-1 injection throughput. The system is very simple, rapid and selective, and has been successfully applied to determine total iron in red, rosé and white wine without any need for sample pre-treatment steps. The results agree well with ICP-AES, which used as a reference method.

From thermometric to spectrophotometric kinetic-catalytic methods of analysis. A review.

Kinetic-catalytic analytical methods have proved to be very easy and highly sensitive strategies for chemical analysis, that rely on simple instrumentation [1,2]. Molecular absorption spectrophotometry is commonly used as the detection technique. However, other detection systems, like electrochemical or thermometric ones, offer some interesting possibilities since they are not affected by the color or turbidity of the samples. In this review some initial experience with thermometric kinetic-catalytic methods is described, up to our current experience exploiting spectrophotometric flow techniques to automate this kind of reactions, including the use of integrated chips. Procedures for determination of inorganic and organic species in organic and inorganic matrices are presented.